• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

The Miter Saw

Best Miter Saws 2020 Reviews

  • Best Miter Saws
  • Best Table Saws
  • Blog
  • Reviews

Cutting Strips On Table Saw – Simple Easy Step to Follow

April 6, 2022 By SK Zai Leave a Comment

FacebookTweetPin

Cutting strips on the table saw is not only dangerous but also a tough job to get done. But the right approach can save you time and effort. Here we will discuss the right and easy techniques for cutting strips on the table saw to get a precise and accurate performance on board.

Cutting Strips On Table Saw

Three Cuts Types for Strips on Table Saw

When it comes to cutting strips on the table saw, it is important to know how many kinds of cuts you can get from it.

A Dado Cut

It is used in joinery and is also known as a trench. It is with a fence or miter gauge with special blades. Using these tools, you can do your job more quickly as well as accurately.

A Cross Cut

This cut is considered to be any cut across the close direction on the board. It can be cut across the grain, and you can do it with the use of the sled and miter gauge.

A Ripping Cut

As its name implies, it goes down to the length of the board. You can complete it only with the fence.

Adjust the Blade Height

Two ways are going to describe the blade height. The first one is, you can adjust the height of the material by using the top edge. It is dangerous such as if you slip, the more able you can damage. It is because you have to cut from the bottom, which minimizes the fraying and tear. But if you are an expert, then it can be safe for you.

You can either set the blade slightly above the top of the material, which is simple as it can be. The material, which you are supposing to be cut, adjusts it higher to approx 1/8 inches. It is the safest way, and you will likely get a smooth cut and suggest for those who want to prevent tear-out.

Angled Cuts

No matter what table saw you are having, there are two angles for cuts. The one is relative to the plane of the table, so you can apply this method by tilting the blade over. Regarding this, you have to change the wheel angle using the reference indicator, which you can find on the side of the machine. To get the most precise level, you have to be sure about the markings on the miter gauge and the machine’s front. Moreover, if you want to get a higher angle cut, you have to use a protector and a bevel gauge. In this way, you will get the correct angle of the blade.

Now the second method is concerned; it; used the miter gauge and relative to the plane of the blade. You can set any angle size by using the milter gauge.

Adjust the Fence

The next thing is to set the fence. You should consider this aspect when cutting strips on the table saw. It will give you an accurate cut so you can control the fence by the level featured at its front. Lift the lever to adjust the width of your cut.

After that, you have to raise the saw blade to measure it slightly. You have to lower down the lever partially to relieve it but don’t firm it down. Hence, the fence will get a proper position.

Another option you can choose is getting the right measurements from the fence to the blade for both front and back.

Here is a tip for you that you both the ways should be same. Otherwise, you have to gently rap on the fence with your knuckles to get the same lengths.

Make A Cut

It’s time to cut strips on the table saw after adjusting the blade and fence height.

To doing so, you have to run on the tool and use force to keep the board against the fence

Pull the miter gauge handle by using your right hand. When it is done, you have to set the gauge to the back of the saw.

By using the left hand, you have to firmly hold your board against the edge. Make sure you have made 6 inches distance from the saw blade cover to avoid any danger. Get a firm grip on the board by using your left hand. First, you have to keep the speed slow and push the miter gauge fence forward to cut your board. After that, eliminate the scrap wood in a light way and shut the machine off.

Above all, these steps are simple as they can be so you can get safety and efficiency at the same time. Still, there are some things that you have to consider while cutting strips on a table saw, as described below!

Do’s

First and foremost, you have to check the material. You should not cut the metal material on your table saw. Not only can it be dangerous, but your tool also gets damaged.

The next thing is to do; you have to retract the blade into the table when you have done.

After that, you should use push sticks as well as blocks.

Lastly, you have to clean up after accomplishing your task.

Don’t

You should not use the milter gauge and fence simultaneously.

Don’t put your hands over in line with blades and material into the fence too hard.

Last but not least, you should do not saw the push sticks and blocks.

The Conclusion

All in all, we have provided you simple and easy to follow for cutting strips on the table saw. There is no doubt a table saw is the most versatile tool, which can be dangerous for you if you don’t follow the right techniques. Hence we have provided the correct and safe way to cut strips softly. You will truly get accurate and precise functionality.
Also Read: How to Cut An Angle on Table Saw?

Related Posts:

  • How to Cut An Angle on Table Saw? Simple Steps to Follow
    How to Cut An Angle on Table Saw? Simple Steps to Follow
  • Types of Table Saw Blades & Adjustments – Simple and Easy Ways
    Types of Table Saw Blades & Adjustments – Simple and Easy…
  • How to Make A Table Saw Fence for Homemade Table Saw?
    How to Make A Table Saw Fence for Homemade Table Saw?
  • Table Saw Basics – Things You Need to Know to Use a Table Saw
    Table Saw Basics – Things You Need to Know to Use a Table…
  • Miter Saw Vs. Table Saw – Which One is Best for You?
    Miter Saw Vs. Table Saw – Which One is Best for You?
  • How To Use A Table Saw? A Complete Guide
    How To Use A Table Saw? A Complete Guide

Filed Under: Blog

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Best Miter Saw for Beginners – Complete Guide
  • Best Table Saws 2023 Reviews – Top 10 Picks And Buyer’s Guide
  • Miter Saw Vs Circular Saw – Comparison, Types Pros, & Cons
  • Types of Table Saw Blades & Adjustments – Simple and Easy Ways
  • Best Jigsaws 2022 – Reviews And Buyer’s Guide
  • About Us
  • Contact Us
  • Affiliate Disclosure
  • Terms of Services
  • Privacy Policy

Copyright © 2023 · TheMiterSaw.com


TheMiterSaw.com IS A PARTICIPANT IN THE AMAZON SERVICES LLC ASSOCIATES PROGRAM, AN AFFILIATE ADVERTISING PROGRAM DESIGNED TO PROVIDE A MEANS FOR SITES TO EARN ADVERTISING FEES BY ADVERTISING AND LINKING TO AMAZON.COM. AMAZON, THE AMAZON LOGO, AMAZONSUPPLY, AND THE AMAZONSUPPLY LOGO ARE TRADEMARKS OF AMAZON.COM, INC. OR ITS AFFILIATES. AS AN AMAZON ASSOCIATE WE EARN AFFILIATE COMMISSIONS FROM QUALIFYING PURCHASES.